Sizing an Off-Grid Solar & Battery System for Total Grid Independence

Sizing an Off-Grid Solar & Battery System for Total Grid Independence
Sizing an Off-Grid Solar & Battery System for Total Grid Independence
October 28, 2026
Sizing an Off-Grid Solar & Battery System for Total Grid Independence

Most off-grid systems fail on paper before they fail in the field: they are sized from guesses instead of numbers. The fix is a load audit — a simple worksheet of everything you will power — followed by three calculations for battery, panels, and inverter. This guide walks through the whole process with a worked example you can copy with your own numbers.

Step 1: The load audit worksheet

For every appliance, record three numbers: watts while running, hours used per day, and the product of the two (watt-hours per day). Check the label on the device or use a plug-in watt meter (about $20–$35) for a day to get real figures — nameplate watts often overstate or understate actual draw.

Worked example for a small cabin or efficient home:

Load Watts Hours/day Wh/day
Refrigerator (cycles on/off) 150 avg. draw pattern runs 24, compressor ~8 1,200
LED lighting, whole cabin 60 5 300
Laptop + phones 65 5 325
Water pump (pressure tank) 800 0.5 400
TV / entertainment 100 3 300
Fans and misc. small loads — — 300
Router + standby loads 15 24 360
Total ≈ 3,200 Wh/day

Round your total up by about 10% for inverter inefficiency and future loads. Our example household designs around 3,500 Wh per day. Note what is NOT on this list: electric stove, electric water heater, clothes dryer, and air conditioning are enormous loads. Off-grid homes typically move those to propane or treat them as optional, generator-backed loads. Be honest at this step — an audit that flatters you produces a system that disappoints you.

Step 2: Size the battery bank

Decide two things: days of autonomy (how long you ride out cloudy weather with no sun) and your battery chemistry's usable depth of discharge.

  • Days of autonomy: 2 days is a common off-grid target; 1 day is the budget minimum, 3 is comfortable.
  • Usable capacity: LiFePO4 batteries are typically used at 80–90% of nameplate capacity. Lead-acid (including AGM) should only be drawn to about 50%, so a lead-acid bank must be roughly twice the nameplate size for the same usable energy.

The math for our example:

  • Usable energy needed: 3,500 Wh × 2 days = 7,000 Wh usable
  • LiFePO4 nameplate: 7,000 ÷ 0.85 ≈ 8,200 Wh — at 48V that is about 170Ah, so a 48V 200Ah-class bank (roughly 10 kWh nameplate) gives comfortable margin.
  • Lead-acid equivalent: 7,000 ÷ 0.50 = 14,000 Wh nameplate — nearly double the bank, which is why lithium usually wins on lifetime cost despite the higher upfront price.

Step 3: Size the solar array

Panels are rated in watts under ideal lab sun. Real output depends on your peak sun hours — the equivalent hours of full sun per day. Much of the U.S. averages roughly 4–5.5 annually, with winter values often 2.5–4 depending on region. Design for your worst month, not your best.

Formula: Array watts = Daily Wh ÷ (peak sun hours × system derate). The derate factor (typically 0.75–0.85) accounts for inverter losses, heat, dust, and wiring.

Worked example: 3,500 Wh ÷ (4.0 winter sun hours × 0.8) ≈ 1,100 watts. Install 1,200W (for example, three 400W panels) as a floor, and consider 1,600–2,000W if you want faster recovery after storms, plan to add loads, or your winters are dark. Oversizing panels is the cheapest upgrade in the whole system — panels cost far less per watt than batteries.

Step 4: Size the inverter

Add up the watts of everything that could run at the same moment — that is your minimum continuous rating. Then check surge: motors (fridges, pumps, power tools) can draw 3–5 times their running watts for a split second at startup. In our example, the pump (800W) starting while the fridge (150W) and lights run calls for an inverter in the 3,000W continuous class with a surge rating around 6,000W, in a pure sine wave model. Modified sine wave inverters can damage sensitive electronics and run motors hot; off-grid, pure sine is the rule. A hybrid inverter/charger also lets a small generator top up the bank during long storms — cheap insurance.

Rules of thumb worth remembering

  • Size from measured loads, worst-month sun, and 2 days of autonomy; optimism is not a design parameter.
  • Battery voltage: 48V systems suit anything above roughly 3,000W of inverter; 12V is for small cabins and RVs only.
  • Every watt of load you eliminate is cheaper than a watt of generation plus storage. Efficient appliances are a system upgrade.
  • Leave 20% headroom everywhere: loads grow, batteries age, panels soil.

Common mistakes

  1. Sizing to summer sun and discovering the truth in December.
  2. Ignoring phantom loads — the router, chargers, and standby draws in the audit above quietly ate 360 Wh a day.
  3. Forgetting surge — the system trips every time the pump starts.
  4. Mixing old and new batteries in one bank; the bank ages to its weakest member.
  5. Undersized cables between battery and inverter, which waste energy as heat and can be a fire risk. Follow the inverter manual's gauge and length specs exactly.
  6. No generator backup plan for the one bad week a year — even a small unit transforms your resilience.

Do the worksheet honestly, and the system you build will simply work, day after gray day. Join The Love Matrix on Facebook — link in the footer. When you are ready to put your design into hardware, browse the Power, Grid & Survival collection at Terrain Matrix for the power stations, panels, and batteries to build it with.

RELATED ARTICLES

Leave a comment

Your email address will not be published. Required fields are marked *

Please note, comments must be approved before they are published